Remote Control Automatic

NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver

NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver
NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver
NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver
NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver

NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver   NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver

The unique design of external mounting plate, easier installation , firmer. The remote control with digital conversion system in sound option, which can not be decoded and duplicated, preventing technical unlocking. Super power-saving control mode, low power consumption, 4 No. 5 batteries can support normal standby for more than 16 months.

The lock body without electricity, the lock can be used with spare battery as usual. You need to worry that the lock can not be unlocked when the battery is dead. Long service life, there is no wear with the operation of 300,000 times. Anti rust battery box, the battery box spring is made of stainless steel , permanent use. The bolt and main parts of the panel are made of stainless steel, never fade.

Can be added with a password keyboard controller and use the password to unlock. Only knowing the password can the remote controller be used as a safer alternate.

Low voltage alarm prompting function and lock protection function under voltage: when running out of the battery power , the remote controller can't lock the door (remote control lock can not be locked and it gives out alarm sound). The remote controller can be used normally, and you should replace the battery.

Can be widely used in Office, home furnishing, hotel, any security door, household door, corridor door, wooden door, garage door. Number of operations: 300,000 times.

Power supply mode: 4 NO5 dry batteries and 23A12V battery , either of the ways can be used normally. Battery life: 4 batteries can support normal standby for more than 16 months. The unlocking current: 100 mA. Service environment: temperature of -20 70 , humidity of 20%80%.

The shift motion of bolt : 23mm. Size: 77mm x 133mm x 37mm. Product picture and introduction of part name 1. Battery box cover plate 3. Battery box cover plate screw 4.

Ear of the bolt 5. Lock body fixed plate 7 Common unlocking button 8 Spare unlocking button Instructions 1 Scope of application: Office, home furnishing, hotel, any security door, household door, corridor door, wooden door, garage door etc. 2 The installation steps: 1 Close the door, place the mounting plate and the bolt between the doorframe and the door tightly, paint several locating holes, then directly use electric drill to fight screws to fix it (refer to the Figure) 2 Fix the lock body bottom plate, tighten 4 screws to fix the lock body. The corresponding bolt base should not be tight, with 2 mm to ensure opening or locking without interference ; 3 After installation, people should use the remote controller inside the door to see whether the lock is flexible , and the bolt should not be stuck. Method of replacing battery: Unscrew the battery cover screw, open the cover plate, remove the batteries and place 4 new No 5 battery.

(Nanfu, Duracell batteries are recommended) 4 Application method: Commonly used circuit switch lock. Lock the door: press (0.5 seconds) on the remote controller, the lock is locked when you hear the sound of the bolt, and the horn of lock body makes one sound. Open the door: press (0.5 seconds), the lock is unlocked when you hear the sound of the bolt, and the horn of lock body makes three sounds. Standby circuit switch lock: standby circuit is usually in off position. When using it, you should beat the door connecting with the lock body (slightly larger strength), with a frequency of about once every 0.5 seconds, do 3--5 times (if the door is very thick, more beats are appropriate), do not beat the door until the horn of the lock body make one sound, while a standby circuit is switched on, immediately press a set of buttons on the bottom of the remote controller, then you can control the switch lock. If you do not press the set of buttons timely when hearing the sound of the horn, the standby lock body system automatically shuts down.

You can repeat the above steps if you want to use standby switch lock. In the process of using, if you hear the alarm sound which shows low voltage for many times, you should replace the battery. Please replace a group of spare 12V batteries together. You can press the key in the remote controller and will hear three sounds let out by the horn, then release matching code key st2 and the remote controller has been set up by then.

2 Repeat steps above in case of requiring setting up other remote controllers. 3 Methods for setting up standby system: Press standby setting up key (ST1) when setting up standby system and the method is the same as above mentioned, except that the standby keys in the remote controller are as keys below.

4 This lock can be matched with password remote controller also. Concrete operations:Before operating on password remote controller, long press common circuit matching code key for 8 to 10 seconds first to delete all codes of the remote controller, then press matching code key ST2 in lock body(release after one press), and then press it again (press and hold), then press key C, hearing the lock body let out three sounds (HXQ901 model let out one sound and flash five times) indicates code has been matched. Then set password by pressing key C, entering password you want (1-6 random numbers) , pressing key C to confirm. Hearing three sounds of tck tck tck indicates that you have set the password correctly. (Do not release each press until hearing the sound) Application method of password remote controller.

Press key C in password remote controller, then keys 123456, then key C (do not press too fast), and then carry out switch operations. Operations of switch lock of password remote controller.

Press key C (one sound), then press keys 1-2-3-4-5-6- to unlock. Press key C (one sound), then press keys 1-2-3-4-5-6- to lock. 5Delete remote controller In case that the controller is lost carelessly, please long press the matching code key(st2) in the lock body to make the buzzer let out a sound, about 8 seconds later the horn gives another sound and then release the key. Press the standby matching code key (st2) for about 8 seconds to delete the standby circuit, with the same methods as above. Application method for telephone unlocking controller.

To enjoy three guarantees (for repair replacement or compensation of faulty products) using this card is only in accordance with the lock within models above. Offer this card when enjoying three guarantees (for repair replacement or compensation of faulty products) 3.

This card takes effect after the lock sales unit has sealed and the operator has signatured. Improper use, safe keep and maintenance by consumer result in damage. The item "NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver" is in sale since Monday, August 29, 2016. This item is in the category "Home & Garden\Home Improvement\Building & Hardware\Garage Doors & Openers\Opener Systems". The seller is "gate-hardware-and-equipments" and is located in Miami, Florida.

This item can be shipped worldwide.

  • MPN: HXQ908
  • Brand: NSEE
  • Type: Automatic Gate Lock
  • Warranty: 1 year warranty from manufacturer


NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver   NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver